SPECIFICATIONS
SpeedyBee F405 V4 30x30 flight controller
STM32F405 MCU
IMU (gyroscope) ICM42688P
Port type USB Type-C
Built-in barometer
OSD Chip AT7456E Chip
Bluetooth BLE supported. Used for flight controller configuration (MSP must be enabled with baud rate 115200 on UART4)
Wi-Fi Not supported
DJI Air Connection Modes Two modes are supported: 6-pin connector or direct soldering.
6-pin DJI air unit plug supported. Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no need to replace any cables.
Blackbox MicroSD Card Slot *Betaflight firmware requires the microSD card type to be Standard (SDSC) or High Capacity (SDHC) less than 32GB, so Extended Capacity (SDXC) cards are not supported (many high capacity U3 cards speeds are SDXC). The microSD card MUST also be formatted with FAT16 or FAT32 format (recommended), you can use any SD card smaller than 32GB, but Betaflight can only recognize a maximum of 4GB. We suggest you use this third-party formatting tool and choose "Overwrite Format", then format the card. Also check here for recommended SD cards or buy tested cards from our store.
Current sensor input supported. For SpeedyBee BLS 55A ESC, set Scale = 400 and Offset = 0.
3S - 6S Lipo power input (via G, BAT pin/pad from 8-pin or 8-pad connector on bottom side)
5V output 9 groups of 5V output, four +5V pads and 1 BZ+ pad (used for buzzer) on the front side and 4 5V LED pads. The total current load is 3A.
9V Output 2 groups of 9V output, one +9V pad on the front side and the other included in a connector on the bottom side. The total current load is 3A.
3.3V output supported. Designed for receivers with 3.3V input. Current load up to 500mA.
4.5V output supported. Designed for GPS receiver and module even when the FC is powered by USB port. Current load up to 1 A.
ESC signal M1 - M4 on the bottom side and M5-M8 on the front side.
UART Set 6 (UART1, UART2, UART3, UART4 (dedicated to Bluetooth connection)), UART5 (dedicated to ESC telemetry), UART6
ESC Telemetry UART R5(UART5)
I2C supported. SDA and SCL padding on the front. Used for magnetometer, sonar, etc.
Traditional Betaflight LED pad supported. 5V, G and LED pad at the bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
Buzzer BZ+ and BZ- used for 5V buzzer
BOOT button supported.
[A]. Press and hold the BOOT button and turn on the FC at the same time to force the FC to enter DFU mode, this is for flashing the firmware when the FC is locked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to the LED1-LED4 connectors on the bottom side. By default, short press the BOOT button to switch the LED display mode. Long press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. In BF-LED mode, all LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI input supported. Named RS on the front side.
Smart Port/F.Port Not supported
Flight controller firmware supported BetaFlight (default), INAV
Firmware target name SPEEDYBEEF405V4
Mounting 30.5 x 30.5mm (hole diameter 4mm)
Dimensions 41.6 (L) x 39.4 (W) x 7.8 (H) mm
Weight 10.5 g
Package Included
1 x SpeedyBee F405 V4 Flight Controller x 1
2 x M3 x 8mm Silicone Grommets (for FC) x 5
3 x 1.0mm 30mm long 8-pin SH cables (for FC-ESC connection) x 1
4 x DJI 6-Pin Cable (80mm) x 1
SHIPPING
Italy
• Express Shipping (1-4 working days)
• Free for orders over €150.00
• €9.99 for orders under €150.00
Europe (European Union)
• International Express Shipping (2-6 business days)
• €29.99 for all orders
PAYMENT METHODS
On Drone24hours.com you can use the following payment methods:
- Paypal
- Visa
- Visa Electron
- CartaSi
- Postepay
- MasterCard
- American Express
- Paypal prepaid cards linked to the Visa or Mastercard circuit
- Cash on delivery
Return Policy
You can return products that you are not satisfied with within 14 days of receiving your order. To be eligible for a return, the product must be in the same condition in which you received it, unworn or unused, with tags and in the original packaging. You must also have your receipt or proof of purchase.
Damaged or incorrect goods
In case you receive wrong or damaged goods, please contact us immediately within 14 days of receiving your order. Please send an email with photos and videos of the product, a detailed description of the problem and what you have done to solve it. You may be asked to return the item. For confirmed defective goods, we will send a replacement free of charge.
Exceptions / Non-returnable items
Some items cannot be returned, such as perishable goods (food, flowers, plants), personalized or made-to-order products, and personal care products (cosmetics). We do not accept returns on hazardous materials, flammable liquids, or gases. We do not accept returns on sale items or gift cards.
Exchanges
If you wish to exchange an item, the fastest way is to return it and place a new order for the new item.
Under the 24-month Legal Guarantee, Drone24Hours is responsible to the consumer for any defects in conformity that cannot be detected at the time of purchase.
The lack of conformity exists when the product is not suitable for the use for which it is normally intended, does not conform to the description or does not possess the qualities promised by the seller, does not offer the qualities and performances usual for a good of the same type, is not suitable for the particular use desired by the consumer if brought to the attention of the seller at the time of purchase and accepted by the seller (art. 129 of the Consumer Code).
Any lack of conformity which becomes apparent within 24 months of the date of purchase of the goods must be reported within 2 months of the date of discovery of the defect.
Unless proven otherwise, it is presumed that any lack of conformity that becomes apparent within 6 months of delivery of the goods already existed on that date. In the event of a lack of conformity, the consumer has the right to have the conformity of the goods restored, free of charge, by repair or replacement (art. 130 of the Consumer Code).
The consumer may ask, at his choice, the seller to repair the goods or replace them, free of charge in both cases, unless the requested remedy is objectively impossible or excessively expensive compared to the other. Repairs or replacements must be carried out within a reasonable time from the request of the Consumer; the average time for returning the product to the Consumer is 20 days.
If Drone24hours is unable to return the repaired product within the maximum period of 60 days, the consumer may request one of the alternative remedies (replacement, termination of the contract, price reduction).
Drone24Hours will send the product for any repairs to the Technical Assistance Center authorized by the Manufacturer.
What happens if the Service Center does not find the lack of conformity?
If the lack of conformity is not found, Drone24Hours will communicate the estimate to the Customer, who can decide whether or not to carry out the repair at his own expense. In this case, any transport costs and diagnosis of the defect requested by the Assistance Center will be borne by the Customer.