Due to the non-production of the Runcam Nano3 camera, now the Mobula7 1s comes with the Caddx ant camera from May 2024. The Mobula7 1s with Caddx ant camera was called V2 version. Please noted.
We are happy to launch our new Mobula7 drone, this time the 75mm whoop based on 1 second power. Thanks to the new AIO flight controller and the new third generation RS0802 brushless motor, the new Mobula7 1s will be the best choice in the whoop season.
The world's first 5-IN-1 AIO flight controller with ExpressLRS 2.0, OPENVTX (up to 400mw), Blheli_S 12A Brushless ESC and newly released Betaflight OSD. This is a great flight controller for Brushless whoop. You could get incredible RX and VTX range using this flight controller.
The new RS0802 motors feature a new unibell design, use a 1.5mm shaft, and include a PCB bottom plate, high efficiency and much more reliable.
New built-in OpenVTX, max power up to 400mw, provides RCE and PIT modes, was very useful for racing events.
Characteristics
X12 5-IN-1 AIO Flight Controller Integrated 2.4G ELRS V2.0 and Openvtx
VTX Power up to 400 mw
ELRS V2.0 support
NEW RS0802 KV20000 engines
Caddxfpv ANT 1/3 CMOS 1200TVL Camera
Smooth and powerful
Compatible for 1S Lipo/LIHV
recommend 1S 450mah/550mah/650mah battery ( not included )
Specifications
- Brand: Happymodel
- Item Name: Mobula7 1S 75mm Micro FPV whoop drone
- Wheelbase: 75mm
- Size: 99mm*99mm*40mm
- Weight: 24g
- Battery Connector: PH2.0
components
The engine | Mode: RS0802 KV20000 Configuration: 9N12P Stator diameter: 8 mm Stator length: 2mm Shaft Diameter: Φ1.5mm Motor size (diameter*length): Φ10.5mm*13.5mm Weight (g): 2.0g No. of Cells (Lipo): 1S only |
Propellers | Weight: 0.24g Material: PC Pitch: 1 inch Tip diameter: 40 mm Central thickness: 5 mm Center hole diameter: 1.5mm |
Flight controller | X12 ELRS V1.0 Flight Controller Integrated 2.4G ELRS Receiver Target: CRAZYBEEF4SX1280 X12 Frsky Flight Controller V1.0 Built-in Frsky 2.4G SPI Receiver Target: CRAZYBEEF4FR X12 PNP V1.0 Flight Controller with External TBS CRSF Nano Receiver Target: CRAZYBEEF4DX X12 PNP V1.0 flight controller without integrated receiver Target: CRAZYBEEF4DX MCU: STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU6000 or ICM20689 or BMI270 (SPI connection) Mounting Hole Size: 25.5mm*25.5mm Power: 1S battery input (DC 2.9V-4.35V) 12 A integrated (each) Blheli_S 4in1 ESC Integrated Betaflight OSD (SPI control) Integrated OpenVTX 5.8G 0mw~400mw Built-in ExpressLRS 2.4G, Frsky D8/D16 Integrated voltage detection Integrated current sensor |
Integrated 4in1 ESC | Power supply: 1S LiPo/LiPo HV Current: 12A continuous peak 15A (3 seconds) Supports programmable BLHeliSuite Factory firmware: Z_H_30_REV16_7.HEX Default protocol: DSHOT300 Supports Bluejay firmware When using Blujay firmware with 48khz, you need to set the boot power to 1100/1200 |
Built-in 2.4GHz ExpressLRS SPI receiver | Packet speed option: 50Hz/150Hz/250Hz/500Hz ExpressLRS firmware version: V2.0 RF Frequency: 2.4GHz Antenna: SMD antenna Telemetry Output Power: <12 dBm Receiver protocol: SPI ExpressLRS Compatible with ExpressLRS V2.0 TX module Unable to flash separate ExpressLRS firmware |
Integrated 5.8g OPENVTX | Firmware version: OPENVTX Smartaudio v2.1 PIT mode support Support RCE mode Channels: 48 channels Transmit power: 0/RCE/25mw/100mw/400mw Power supply: DC 5V Current (5v):650ma~1000ma |
ANT Caddxfpv camera | Image sensor: 1/3″ CMOS sensor Horizontal resolution: 1200 TVL TV system: NTSC or PAL PICTURE: 16:9 or 4:3 Synchronization: Electronic shutter internal : PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N ratio: >52 dB (AGC OFF) Video Output: CVBS Lens: 1.8mm Min. Illumination: 0.001 Lux@F1.2 Automatic Gain Control: YES WDR: Global WDR DNR: 3D DNR Size: 14*14mm (with bracket up to 19*19mm) Wide power input: DC 3.7-18V Weight: 2g (NW) |
Recommended parts
- Gaoneng GNB 660mAh 3.8V 1S 90C/180C HV 4.35V PH2.0 plug with wire
-
Gaoneng GNB 660mAh 3.8V 1S 90C/180C HV 4.35V PH2.0 plug
Package Included
- 1x Mobula7 1S 75mm whoop drone frame (Mobula7 v4 frame)
- 1x RS0802 KV20000 brushless motor
- 1x Gemfan 1610-2 double-bladed propellers (4cw+4ccw)
- 1x Caddxfpv ANT 1/3 CMOS 1200TVL Camera
- 1x Openvtx integrated 5.8G 0mw~400mw VTX
- 1x 1S Parallel Charging Board
- 1x Propeller disassembly tool
- 1x Additional Camera Canopy
PLEASE NOTE: TO ENSURE THE MAXIMUM QUALITY, EACH MODEL WILL BE INSPECTED BY OUR STAFF BEFORE BEING SHIPPED.